steering knuckle

It was presented that a new precision forming technology of car steering knuckle in this paper.

文章提出了轿车转向节精密成形新工艺.

The production of domestic, import models of the steering section of the main pin, steering knuckle kingpin repair kit is more popular with users alike.

所生产的国产、进口车型的转向节主销、转向节主销修理包更受广大用户的一致好评。

Tie Rod End To Steering Knuckle Nut

转向拉杆端与转向关节螺栓

The effect of thermomechanical treatment on the microstructure and properties of the automobile steering knuckle was researched in this paper.

研究了汽车转向节锻后余热淬火工艺对钢的组织和性能的影响。

Numerical simulation of car steering knuckle obliterated extrusion forming

轿车转向节闭塞挤压成形过程研究

The trike frame should now be nearing completion and only requires the installation of the steering knuckle mounting plates to be complete.

该三轮车框架现在应该已接近完成，只需要安装指导安装板的关节完整。

Thermomechanical Treatment for the Automobile Steering Knuckle BRAZING OF HEAT EXCHANGERS IN AIR-CONDITIONER

汽车转向节形变热处理

Steering knuckle tie rod end pressure lubricator Grayioc tubing joint

转向节横拉杆接头油嘴

This backplate requires modification prior to installation on the steering knuckle.

杠杆,这背板需要修改的背板安装前关节.

Architectures, controls parameter and learning algorithms of the NN of the forging process of the steering knuckle are also studied in the paper.

本文同时针对转向节锻造设计神经网络的类型、控制参数和训练算法进行了研究。

The knuckle arms are secured by keys in the holes of the steering knuckle.

该节武器担保金钥孔的转向节.

Route sensor wire from steering knuckle to fender panel.

从转向节到防护板安排感知器导线走向.

The results show that the thermomechanical treatment can improve the quality of the automobile steering knuckle.

结果表明,锻造余热淬火工艺对汽车转向节质量有明显改善.

Steering knuckle tie rod end pressure lubricator What welding methods do you use in connecting the plates, frames, and beams?

转向节横拉杆接头油嘴在焊接钢板，肋骨，甲板横梁时，你们用什么焊接方法？

The mechanics analysis of returning positive effect of steering knuckle king pin on vehicle

车辆转向节立轴内倾回正作用的力学分析

Steering axis inclination is the inward tilt of the steering knuckle at the top.

转向轴倾角是向内倾斜的转向关节在顶部.

Remove the steering knuckle from the strut.

自支柱拆除转向关节.

During steering maneuvers, the strut and the steering knuckle ( through the ball joint and a pivot bearing in the strut's upper retainer) turn as an assembly.

车辆转向时，支柱以及转向关节（经由球形接头与上支柱固定器之轮毂轴承）会一体旋转。

Set the scope of change within the pivot shift lever, shift rod outside the fulcrum, the connection point under the steering knuckle arm and lower arm coordinate frame connection points, using ADAMS/ Insight to optimization model.

设定转向拉杆内支点、转向拉杆外支点、下摆臂转向节连接点、下摆臂车架连接点等坐标值得变动范围，利用ADAMS/Insight对模型进行优化。